According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
hi,
My custom board running Mesh SDK0.92 send and receive messages are normal.But after I replaced the MeshSDK in my program with Mesh SDK1.0.0, I was unable to send and...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I set the WDT timeout in the application is 5s, when entering the BootLoader set the WDT time is 10s, how...
I am new to ble programming.
I am trying to find the best way to send json objects from android app to nrf52 chip.
What is the best way to send the json object to the...
Hello Sir,
I have developed small and compact product using nRF52832 Soc. Due to size limitation and device is portable. I have attached snap shot of power supply circuit...
Hello sir,
I am develop us product using nRF52832 chip on DK board use S132 soft device and its working well fine. So now we are designing hardware PCB of my product for...
Hello, I am trying to use adc with the uart so i can monitor the readings from adc. But when I include both drivers (nrf_drv_saadc , nrf_drv_uart) i got a confliction error...
Hello, although i have included every library and c file that is needed. i still get a declaration error. I'm almost sure that i enabled everything in sdk_config . I'm kinda...
In sd_power_system_off()，the nrf51822-board current is 2uA；And I think the current in sd_app_evt_wait() will be ~4uA(Is it correct)?
In sd_app_evt_wait(), the code...
In this example project
nRF5_SDK_12.3.0_d7731ad\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\main.c
/**@brief Function for initializing...
Hi,
I am trying to migrate to SDK14.2 from SDK12.
I have succesfully migrated to SDK13, but I am seeing linker issues with 14.
The linker comes with the following errors...
