Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
I purchased a pair of FTDI cables, and I can't seem to get them to work.
Unsure if the pinout is standard but here is the mapping of the cables provided:
Red wire： 5V...
I am using the N548 with the S310 soft device. I have set up the device for asynchronous communication via the UART. I can send ANT+ commands via the UART and I get valid...
Hi there,
I am quite new to BLE.
I am about to buy a nRF51822 Bluetooth Smart Beacon Kit. But before that I would like to be sure if I am able to advertise battery level...
Hi,
We just recently received our (custom) board with the nrf51822.
To program and debug the nRF I use the pca10028 and the debug out header.
I wrote a very basic program...
I tried loading SoftDevice, Bootloader, and Application using the SoftDevice and Precompiled hex files that come from the example code version v1.1.0. I am using nRFgo Studio...
While attempting to update the firmware from a HEX file, the DFU Application in the nRF Toolkit reports that the upload failed with an unknown error 22. I was sniffing the...
I have a bootloader running on my NRF51822. It uses a relocated vector map in RAM and jumps to function.
I therefore have two debug files and source code sets.
Does...
I am using nRF51 SDK with version 7.2.0, s110_nRF51822 with version 7.1 and gcc_arm and connect the pca10031 board via JLink and try to load bin files but it returns error...
Hi all,
I'm having problems into making the virtual COM port of the nRF51 DK work.
The only line in the User guide regarding it's configuration is the following:
...
Hi,
I'm usind SoftDevice S110 version 7.1.0
Since I implemented a Radio Activation Hook, my software crashes when a connection is being established. I get the following...
Hi Nordics.
I want make a central device(server) that can collect 6~7 peripheral's sensor data with multi-connection.
The central device will transfer peripheral's sensor...
Hello,
I just want to add SPI master module into the ble_app_uart application, and only add spi_master.c and .h into this project with no any other change, and just call...
Hi,
I'm using gcc with eclipse to compile ble_app_hrs and I get the following error for all the SVCalls like sd_softdevice_enable, etc...
The following error is flagged...
Hi , I need to develop an indoor positioning project based on Bluetooth Low Energy 4.0 in which i have to locate person's current position in home and send it to main server...
