Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
I tried changing the broadcast name which was not easy but after installing the nRFgoStudio and editing the XML file with it - I managed to change the name yet the UART program...
For some sort of geofencing application, we want to include the BLE module nRF51822 into a Base Station (BS), and a small mobile device (MS).
The MS should detect the presence...
I have 2 moduls from ebay (rfinchina). I write little librarie for nRF24L01 and my msp430.
When i start my coard and init spi and try read few register - i have problem....
Hi,I use 51822 to make a fitness device. one of the function is advertising current value(Steps,Heart rate,Distance,Calorie) to the phone over BLE. What the default service...
I downloaded nRF51 SDK 5.2.0 and I am studying the examples for S120.
I notices that there's no gcc directory, thus only Keil compiler can be used. Is there a way to use...
Hello,
I have some questions regarding bluetooth low energy and the NRF51 series.
[list=1]1) I have to synchronise maximum 17 sensors, so i will maximum need 4 masters...
Hi.
I am looking for the internal resistance of the ADC pin of my nrf51822. I have looked at the Product Specifications (as well as the Reference Manual and other documents...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
