The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
Hi all,
I test the DFU as follow:
erase chip, program "s110_nrf51822_5.2.1_softdevice.hex"
program "bootloader" by using nrfjprog.exe
"DfuTarg" can be found...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to build the bootloader for gcc/Eclipse.
I used the manual setup approach described here.
However, I can not fit in the allocated space, because...
SDK version: 5.1.0
S110 version: 6.0.0
chip: nRF51822
I am experimenting a generic Data transfer hid device, the report map is as follows:
0x05, 0x0C, // Usage...
Hello Nordic team,
I am working on a BLE RedBearLab shield (nrf8001) mounted on an Arduino board.
Consider that a connection is correctly made from a Master app to my...
I've been running various code on a 51822 that has used PPI, timers, events, GPIO pin config and so on. Supposing I've lost track of what state the retained registers on the...
Hi,
I am new to ANT programming, and was following the userguide's steps to set up my nRF51422 evaluation kit (pca10003 board). I can compile and upload the blinky example...
Hello Guys,
I am having a hard time figuring how to add the nRF51xxx algorithm into Keil. According to nRF81522 Evaluation Kit user guide this should have been installed...