We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
C:/ncs/v2.9.1/zephyr/include/zephyr/toolchain/gcc.h:87:36: error: static assertion failed: "/soc/peripheral@50000000/uart@c7000 defined without sleep state" ,when i use the...
I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I am starting with Nordic nRF51822 and I would like to know if do you have some samples for use with emIDE (I liked it because you don't have size limitation). And I had some...
I saw two different way to ini ble
1 ) BLE_STACK_HANDLER_INIT
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false);
err_code = softdevice_ble_evt_handler_set...
I'm right now getting uC to sleep WHEN THERE ARE NO ACI EVENTS I think I'm doing right, the uC sleeps but I'm not able to wake up despite the fact that RDYN is connceted to...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Using sdk5.2, and ble_bondmngr_bonded_centrals_store() called on_disconnect, and then call
err_code = sd_ble_gatts_sys_attr_get(m_conn_handle,
m_central.sys_attr.sys_attr...
Hi!
I wonder what is the GPIOs nominal voltage level when I'm using the internal DC/DC converter?
I know that the internal DC/DC converter output voltage is 1,9V but I...
Hello,
we made PCB based on reference with ST balun. In circuit the low freq crystal is optional, so we didnt use it. In software i noticed app_timer use RTC timer. So the...
I am trying to bootload an extremely large hex file using a slightly modified DFU (modified from SDK v5.2.0's example)
The problem is that the hex is so large that eventually...
Im having errors like Arduino is in the while(1) loop if I enable the DC/DC converter in the characteristics and generate service.h file , If I do not use this setting everything...
I have a NRF24L01 board, which acts as a receiver. It listens on RF channel 2 using address pipe 0 address as follows 0xC47B4D0331. I am able to transmit to this NRF24L01...
I need to wake my uC from sleep when the nrf8001 gets in connected mode and for that I need to supply an external interrupt on hardware interrupts on the MCU.
Will active...
www.dropbox.com/.../error.jpg
it is not even reach main()
same as devzone.nordicsemi.com/.../nrf51422-flashes-ok,-but-debugging-fails-stays-in-moves-r0,r0
is it related...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
