Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hello,
Does anybody know what I could be doing wrong either on peripheral or PC when my program on PC reports this error?
I am in the process of writing an application...
Good morning. Thanks for reading. I am brand new to development on Nordic platform but fairly experienced with ARM Cortex, GCC, IAR, Eclipse, etc.
I have a the PCA10003...
Hey guys. I'm very new to Bluetooth 4.0 (actually Bluetooth in general), but I'm hoping to be able to use a Fujitsu MBH7BLZ02-109004 module with an nRF51822 in a product I...
I am attempting to measure battery voltage through the ADC, but am getting inaccurate results. In my setup, I have a 4.2 V battery divided down to the bandgap range using...
HI all:
I am using the nrf24le1.And i confuse about the recive and transmission address in rf transceiver.
What do we use the address to do usually.It will be wonderful...
Copy nrf51.cdb to "C:\Keil\UV4"
Copy nrf51xxx.flm to "C:\Keil\ARM\Flash"
Set the keil project-device to nRF51822(data base : Nordic nRF Series Devices)
This is...
Hi
Is there a documentation of the nRF51822 sniffer interface? e.g. communication structure, command format, captured messages structure etc?
Thanks
Yaron
I'm trying to set up a network where 1 - 4 BLE devices wirelessly talk to a computer. I'm using an arduino connected to the BLE shield.
The computer is a Winows 7 laptop...
Hi,
I'm creating a project on nRF51822 chip and I have a problem with disconnection. In my program I want to disconnect with master after some time e.g. 30 seconds. I'm using...
I'm unable to write my application code to the flash of an NRF51922 (QFAACAA). NRF Studio will let me flash the hex file but it fails verification. If I try programming in...
I have a question, can nRF51822 operate in regular Bluetooth mode like a Bluetooth 2.1 device?
If answer is no then, is there any product from Nordic that operate as Classic...
Hi developers,
I've finally got the nrf51822 working and advertising a good signal to the dongle. :)
After doing all the steps in the NAN-36 pdf-file I hoped that pressing...
Hi all,
I'm using Timer2 while having the SD enabled, and I'm having some problems. I don't seem to be able to reliably set the periodicity of the timer. No matter what I...
I've spent quite a while getting Eclipse on Mac OSX working. I started with the original makefile but have come up with, finally, a working native Eclipse build which does...
Hi all,
I have an external dongle (Bluegiga) that is scanning for BLE devices.
My problem is this: all the BLE devices in my room are showed correctly except my nRF51822...
