Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
HI,
I am using sdk 8 and pca10028 dk. I follow following procedure,
Program the softdevice using nrfgo
Program the test_bootloader using nrfgo
Program the application...
I have some questions about how I will use this structure ,first of all I know that The "data" member of the ble_gatts_evt_write_t is meant as a placeholder for the address...
I am trying to create a windows app that will read data from an accerometer via a nrF8001 ble module.are there any example i can see for communication between windows and...
Hi, Nordic Engineers. Now, i use a external 32mhz crystal on my board. i have add code"NRF_CLCOK->XTALFREQ = 0X00", but the BLE radio seems not work. Led flick is ok.
Why...
Hi Guys,
I have a SITECOM Bluetooth Dongle connected to my PC and I want to receive data from nRF51 DK via bluetooth (for example heart rate monitor data).
Could someone...
Hi everyone,
I must to comunicate from HW to PC with SPP over BLE. So I took the dongle BLED112 (side PC) and the HW where is mounted a nrf51822 like uart BLE interface....
Hi,
the product specification of the nRF51822 states the possibility to carry quadrature demodulator
signals on GPIO pins.
This would let one allow to observe the physical...
Hi,
I am a newbie to nrf, I am trying to understand the lbs example while running on nrf dev board. I want to set my application as follows:
Blinking LED while advertising...
Hi, I have a problem with the HFCLKSTARTED interrupt.
I can't have it. (I'm a little bit pressed with time I have to send a document in 2 days, so if you can quick respond...
We are currently using SoftDevice 5.2.1 and was given the task to migrate to 6.2.1. I doing so, I placed 6.2.1 hex onto our device and turned it on. Yikes, many errors. Most...
Right now i have based myself on the BLE UART example where it is UART over BLE.
So naturally I use ble_nus_string_send to send data. After some digging I saw that this...
