Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi,
In many places in the nRF51 documentation (e.g. developer.nordicsemi.com/.../a00081.html) the term "Master Control Panel" is used without clarification that this is...
Hi:
i use SDK7.0 , i write data in flash (address:0x0003fc00)and the data is erased when SDK run.
and is there any way to protect the page that i want to write or...
Any recommendations of power ic to be used in an nRF52 based system?
I am thinking of using DC-DC converter from LTC3553 . Is DCDC converters a good choice for powering nRF52...
Hello,
I am basing a design on the reference design from the nRF-DK (pca10028?). I am trying to understand the implications of using an SMA connector footprint for testing...
I tried to get the ANT background scanning example to work on a PCA10028 and it jumps to softdevice_assert_callback when opening the ant channel. Downloaded everything fresh...
Hi Guys,
I'm new to using the nRF51822 environment but I've used AVRs for years, so please be gentle...
I'm wanting to drive a strip of WS2812 RGB LEDs from an nRF51822...
So I have my nRF51822 updating the characteristic value and sending notifications once every time I receive a radio notification.
uint8_t readings[20] = { 0, 0, 1, 2, 3...
I'm trying to set up TIMER0 to interrupt the timeslot 500us before its end.
It doesn't seem like the NRF_RADIO_CALLBACK_SIGNAL_TYPE_TIMER0 signal is happening, I've put a...
When I try to enable SD having earlier initialized Gazell (SD resources variant) sd_ble_enable() returns 2 (SOFTDEVICE_NOT_ENABLED). If I remove the Gazell initializaton it...
I am trying to work with a custom 3rd party BT 4.0 peripheral device which uses an nRF8001 to transmit data as temperature values in the Bluetooth Health Thermometer service...
Hi,
Slight problem here with bootloader updates : right after download, I copy from SWAP (0x16000) to normal location (0x38000 in my case).
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;...
I am wondering how to precisely measure my power consumption. Till now, I have been using INA216 on PCA10004 board + labView for acquisition, but it is not precise enough...
I was working my way through the app note nAN-36, where it says you should have a seperate source and header file for each service. However in many of the newer SDK examples...
