Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello
I'm trying to implement interfacing between BME280 and nrf52840 on a custom board using zephyr BME280 sample example. I'm using SPI for the interface but there no...
I am evaluating the nRF Connect SDK for nRF5340. Currently, nRF Connect SDK seems to use zephyr's open source stack as the BLE stack.
By the way, nrfxlib / ble_controller...
I am developing application for nRF5340. I have two questions.
1. What value VTOR when reset? ApplicationCore'VTOR==0x00000000/NetworkCore'VTOR==0x01000000 ?
2. How to...
Hi,
i'm a beginner. now only i start with Segger studio & ble concepts.
i need internal RTC with calendar formats? i have check with the example programs , avail only...
Hi, I'm having issues connecting to the ble_app_ots example application from the nrf connect phone app. I have attached a trace from wireshark, and for comparison what it...
Hello,
I tried the basic proprietary rf code that is esb_prx and esb_ptx on the boards and the communication is very fine. The default set of data that is 0x00 to 0xFF is...
Hey! I'm writing a program for communicating the laser sensor pmw 3610 (pixart) with the micro nrf52832. In the sensor datasheet it is said that the time between sending the...
Hi:
I am an engineer from China. Visiting infocentre in China is quite slow. I found some offline documents for nRF5_SDK in https://developer.nordicsemi.com/ and they are...
As the subject description.
I have already test the official sample buttonless_dfu_app and the secure bootloader already. It could work for OTA fucntion.
And my application...
Hello!
I am new to controller programming. My work at the institute is connected with bluetooth research, so I need to learn how to program nrf52840. My microcontroller...
So I looked at the example of the temprature read and I got the following code:
But the problem I got is with the: while (NRF_TEMP->EVENTS_DATARDY == 0), I don't want...
I read the discussion in the following link, but my application is different so I want to ask for advice on how to proceed.
https://devzone.nordicsemi.com/f/nordic-q-a/50642...
Hi all,
I successfully flashed the peripheral_hr sample from the Getting Started guide into my nRF5340 PDK (from here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
