Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello
I'm trying to implement interfacing between BME280 and nrf52840 on a custom board using zephyr BME280 sample example. I'm using SPI for the interface but there no...
I am evaluating the nRF Connect SDK for nRF5340. Currently, nRF Connect SDK seems to use zephyr's open source stack as the BLE stack.
By the way, nrfxlib / ble_controller...
I am developing application for nRF5340. I have two questions.
1. What value VTOR when reset? ApplicationCore'VTOR==0x00000000/NetworkCore'VTOR==0x01000000 ?
2. How to...
Hi,
i'm a beginner. now only i start with Segger studio & ble concepts.
i need internal RTC with calendar formats? i have check with the example programs , avail only...
Hi, I'm having issues connecting to the ble_app_ots example application from the nrf connect phone app. I have attached a trace from wireshark, and for comparison what it...
Hello,
I tried the basic proprietary rf code that is esb_prx and esb_ptx on the boards and the communication is very fine. The default set of data that is 0x00 to 0xFF is...
Hey! I'm writing a program for communicating the laser sensor pmw 3610 (pixart) with the micro nrf52832. In the sensor datasheet it is said that the time between sending the...
Hi:
I am an engineer from China. Visiting infocentre in China is quite slow. I found some offline documents for nRF5_SDK in https://developer.nordicsemi.com/ and they are...
As the subject description.
I have already test the official sample buttonless_dfu_app and the secure bootloader already. It could work for OTA fucntion.
And my application...
Hello!
I am new to controller programming. My work at the institute is connected with bluetooth research, so I need to learn how to program nrf52840. My microcontroller...
So I looked at the example of the temprature read and I got the following code:
But the problem I got is with the: while (NRF_TEMP->EVENTS_DATARDY == 0), I don't want...
I read the discussion in the following link, but my application is different so I want to ask for advice on how to proceed.
https://devzone.nordicsemi.com/f/nordic-q-a/50642...
Hi all,
I successfully flashed the peripheral_hr sample from the Getting Started guide into my nRF5340 PDK (from here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
