Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am trying to perform a large SPI transfer of 72576- 104976 bytes to an nRF52840 SPI slave. I'm running into an error thrown by the SDK indicating that this length is invalid...
hello,When the device's pairing record is lost, the phone's is in.stack report PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING What should I do? NEF52832,SDK15.2.0,S132
I am trying to use the Zigbee SDK to develop a device to connect to older legacy ZigBee HA coordinators. To do this, I need to use the zb_ha_ez_mode functions detailed in...
Hi, we are evaluating possibly using OTS in our product. We are currently on SDK 15.3.0 and when I look at the documentation:
https://infocenter.nordicsemi.com/topic/com...
Hello,
I really need your help with my problem.
I have a sparkfun nrf52840 mini which is the peripheral, using the code ble_app_uart, and a smartphone with a custom...
I'm compiliing against version 1.1.0 of the ncs, and my device have the mfw 1.1.0 firmware running.
When starting the device, I get the following output:
This is not...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I am new to DFU feature on Nordic. I have...
I have custom board with nrf 52832. I am using SDK 15.2.0. and soft devices s132 V6.1.0 to transmit advertising packets with advertising interval 1s. I have written simple...
Hello :)
After upgrading the modem firmware of the nRF9160 to version 1.1.0 (mfw_nrf9160_1.1.0.zip) the call to getaddrinfo returns error 12.
If I downgrade to version...
Hello, everyone~
A new requirement is generated from my customer. He wants the ANCS can transmit more than 20m in a house. So I want to know if BLE 5.0 long range can transmit...
Hello!
I am dealing with nrf52832. I want to process data reception with SPI during f_write processing. Is this possible? As multi-thread processing 1) PT_THREAD in pt...
I'm developing a wearable device using nRF52832. I am developing OTA-DFU nowadays. I have successfully tested the buttonless OTA-DFU using the nRF52-DK.
And I'm testing...
Hi, I have a nRF9160 and I am currently working with the gps example: ncs\nrf\samples\nrf9160\gps
When I run the example, I only see
all the time. I went out on a big...
Hello,
i am struggling with the implementation of i2s to use it one SK6812 Leds.
To start with i used this https://github.com/cheehieu/nrf52-sk6812-led-driver example...
Hi All,
I study this post to enable long-range(s=8) on ble_app_blinky ( nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_blinky )
In the post, one of the settings...
