Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I am using TWI 0 to communicate with an external EEPROM. 99% of the time this is going succesfully. For reasons best known to itself, my eeprom will sometimes fail to acknowledge...
Hi everyone,
I have an nRF52840 DK. So far, I have been programming the nRF DK using the UBS connector J2 and everything worked great.
Since yesterday, by following the...
I want to update status in manufacturer specific data of advertisement packet. is there necessary to stop advertising first then reinitialize advertisement data and again...
Hello peeps,
nRF52480 I2C Interface with Invensense ICM 20948. I am using SDK 15.2. I see there is some Support for MPU 6050 Invensense but not for ICM 20948. A lot of Registers...
Hello,
I am currently working on the nRF SDK for Mesh v3.1 and I am using a static provisioner as in the light switch example. I have merged the client and server functionality...
Hello! I have a custom board with a NRF52832 chip that is working fine with the last program I flashed into. But since yesterday I can’t access it to load a new code (flash...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
nrf52832 , I have flashed ble_peripheral/ble_app_uart with simple modifications
ble doesn’t advertise while Jlink/seggar debugger is connected to our custom board.
...
I use SDK16.0
use BLE + Multiple Beacon, Beacon use timeslot,BLE use softdevice.
I want to modify the advertising content of BLE,But use advertising_stop->advertising_init...
I'm currently working on integrating modem FOTA updates into my application. I have the FOTA working at the moment, I'm able to go to and from a FOTA-TEST version with the...
I try to run this sample https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/mqtt_simple from the master branch, but when I connect to the network...
I'm connecting the battery to the VDDH 3.6V or 3.7V and sensor to VDD, it means nrf52833 get powred on from VDDH and sensor get the power from VDD. is it ok? please check...
