Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi!
I´m currently using the nRF52840 demo board to determine the bluetooth range of the device I'm working on.
The question is: which is the orientation of the antenna...
Hi
We are using PCA10040 for a development and we are using P0.8 , we were setting it up to be No connect when low (IE Open collector) but it was being driven high and we...
I am getting this error message when I tried to complete the initial set up.
There was an error adding your device: No device found with id 'nrf-352656100352817'. Verify...
Hi,
I have a few questions regarding the modem FW updates on the nRF9160.
1. It is my understanding that for new major versions of modem FW (i.e. Feature releases) there...
Hi. I want to broadcast the value of some sensors. But it has to be accesible at the same time for different devices. Up today i developed the system with a UART over BLE...
Hi
After doing a rebuild of a previously working project, my personal phone and a test phone is unable to connect to our product.
The device is discovered by the phone...
Hi,
I'am using sdk14.2 with S140 V5.0.2-alpha.
I want to measure a time execution of a snippet code (ciphering function), and i want to display the time value with NRF_LOG_INFO...
Hi, Wizzards
I understand that the QSPI is made solely for external flash, but we are in a hurry to make a driver for a RGB LED module with a common clock. It would be good...
I have been using nRF Toolbox –DFU to reflash my project. I am using an Android tablet version 6.0.1. This process was working very nicely.
On 2/5/2020 the tablet updated...
Hi,
I have a really hard time with nRF connect. I wrote a simple app for my Dongle and when I want to program it via nRF connect it says that Device not found due to failure...
Hi,
We're trying to add a custom service to the HID keyboard example. the service is initialized we can see the service when connected to the device from the nrfConnect...
I tried original ble_app_hids_keyboard_pca10040_s112 example, then modify it by moving the code for typing h.e.l.l.o from Btn 1 to Btn3, and all possible combination of sd_ble_gap_disconnect...
I've tried using LESC without bonding, but iOS displays a pairing dialog. I don't think it is possible to avoid this, so the only way to avoid the pairing dialog is to use...
