Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
I need to add new files to the aws fota example for the nrf9160 project in order to implement compatibility with the
AWS OTA update agent, I have read other posts in the...
Hello,
I've been starting to get into level 0.1 programming after being able to loosely control an LED with GPIOTE and a timer interrupt using examples and API references...
Hello everyone,
I want to measure current of the whole board, I follow the instruction of nRF52840 DK , which suggest not to use the USB connector to power the board.
...
I am using Rowley CrossStudio 4.4 to debug my project. I can program and step through the code just fine, but I can't seem to get any debug out put on the Debug Terminal....
(1) Production Programming using CLI:
We are entering pre-production for a design containing an nRF52810 (on Rigado BMD-330 module), and we need to know what the CLI command...
Hi,
I was referring the timer example code for PCA10040. I wanted to include the timer code in my ble peripheral code which uses custom GATT service. Can you help me with...
I see that the nRF9160 DK has both cellular and BLE capabilities because it has both a nRF9160 SiP and nRF52840 SoC. Wouldn't it be optimal to combine both cellular and BLE...
Hi There,
The attached image shows the part of the schematic responsible for the enabling of the QM14501. I was wondering if there was a particular reason that the mosfet...
Windows 8.1, 64bit PC
I have a nrf52840 app that works from "SEGGER Release 4.30 Build 2019101800.40379 Windows x64" on the DK 16.0.0, and from " nRF Connect for Desktop...
Hi there,
I want to implement the BLE dfu in nrf zigbee and thread sdk but there are no examples provided in the sdk and if i try to use the files from nrf 52 SDK for...
Similar to this ticket , we are no longer able to connect to Verizon using a Hologram SIM after upgrading modem firmware from 1.0.1 to 1.1.0.
I'm attaching a matching console...
Inside gps_controller.c
We issue the following instruction to begin searching for a satellite fix.
k_delayed_work_submit(&gps_work.work,K_SECONDS(CONFIG_GPS_CONTROL_FIX_CHECK_INTERVAL...
Hi,
We are atempting to get DFU over UART working in our project, but there does not appear to be a bootloader project in the 16.0 SDK for this configuration. What would...
