Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am using 2 development kits 52840-DK.
I run the examples projects transmitter ( pca1056 ) and receiver. It works,
In an attempt to get longer range I increased...
Hi Nordic,
I had built a BLE custom service which has two characteristics and now I'm merging this with light-switch example, but while building it i got a problem which...
Dear All,
I'm pretty sure this has been asked many times but I don't know the right keywords to search for.
Alright, on our custom board we have a PMIC with regulated...
I try to start working with the nRF9160-DK. I gone trough all steps of the Getting Started Assistent from nRF Connect SDK. But i have a Problem with setting up a Project in...
Hi,
In my NRF52840 based application, I have a situation where the peripheral needs to pass 2K to central.
In order to speed up the xfer, I'm requesting a Connection Parameter...
Hi,
I am using nrf52832 and I want to build a device that can advertise iBeacon signals and can transmit data to another BLE device (central) simultaneously.
Can I do...
Hi,
I use example nRF5SDKforThreadandZigbeev3209fade31\examples\dfu\secure_bootloader\pca10056_uart to upgrade bootloader and coordinator application.
I try to upgarde...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
Can we alter the eddystone tlm (telemetry) packet to send custom data . [This is not following the standard packet structure].
But I wanted to know how to alter the given...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
