Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello, Nordic Team! I am encountering a such problem when using the NRF54L15 on NCS3.0.2 to develop a Matter product. I am trying to use the
SubscribeAttribute
method...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Hello,
will the Systick be sourced by the LFCK when in WFI/WFE low power mode (SYSTEM ON IDLE)? On nRF52 series the freeRTOS port uses the RTC as systick for its tickless...
Hi all,
I'm developing a board based on nRF52832.
I want to implement delay power on and power off through holding a single power button for about 3 seconds.
Regarding...
I am try to make twi communication and i got strange issue.
When i use twi scanner example with unconnected pins on my board , i am not see any requests
Great oddity that...
Hello,
I am working on nRF52382 IC. I am accessing GPIO also. But still i don't get the access of antenna. I have make the circuit as per the development board of nRF52...
Hi,
What is the practical maximum throughput of nRF proprietary protocol? The following table showing ESB and GAZEL has 1.3Mbps and 128kbps respectively.
https://www.nordicsemi...
Hello,
I am developing application based on nRF52833 DK. Basically, my application scans all iBeacon messages (ADV_NONCONNETABLE) and transmit to computer.
I would like...
Dear All,
I need your help because I created a PCB with the nrf52840 and a flash connected exactly as the one on the dev-board.
The only difference is that the one on...
I am using nrf52840 . I am sending data 2 bytes as FF .I put the data in 2d array like this. char dataSend[1][5]={"FF"}; This char dataSend has 1 row and 5 length .This should...
I need transfer data to/from NRF52840.
I see I can do it by using function nrfx_usbd_ep_transfer - but don't see any examples.
I want to make bulk endpoint and be capable...
Hi,
I am running ble_app_blinky example on nRF5280 custom board, it is giving me Error 133 (0x85): GATT ERROR . Since I have nrf52DK, I tried same example with SD 132 on...
Hello,
i am using the NRF52832 and the NRF52840 with different softdevices. Now I want to update the softdevices over the air and I need the SD Version strings of all the...
A bit more detailed: A bug has been detected on the device under development. It is connected with the fact that if you try to disconnect a connected device on an iMAC Catalina...
Hi
I am trying to install the SES toolchain on my PC (Win 8.1) following exactly the nRF Connect v3.2.0 Getting Started Assistant. When trying to "Open nRF Connect Project...
I am using a nRF52 DK to program an externally powered board with a NRF52811.
I am able to flash a blinky program onto the custom board successfully using the output .hex...
Just as the title says, I'm trying to measure an input pulse width using PPI and GPIOTE. I am currently measuring the pulse width using timer interrupts, but I would like...
