Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello, I am compiling an application to be flashed onto a nRF52810. I am using Segger Embedded Studios and the nRF52 DK to develop the application. I want to read values from...
Hello All,
I have nrf52810 chip. using softdevice 6.1.1
I have implemented dfu feature.
Now i have implement tx power change feature through nrf connect mobile app...
Me and my team have been working for a couple of months on a custom firmware code for nRF9160 on a custom PCB, based on mqtt_simple and asset_tracker which basically reports...
I have been working to get the secure_bootloader examples to run on the NRF52832_XXAB (QFAB with 32kB RAM and 256kB Flash).
Apart from the fact that I had to change the...
Hi,
Good day!
Problem statement:
TSM12 Capacitive touch sensor IC (I2C com supported) is used in our application. It has got 12 output channels and Channel 1 is a parallel...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
Now I am using nrf9160DK for development. In my project, I need to use a random number generator and a highly accurate system time stamp. Is there an API that I can call directly...
Hello,
On nordic nRF9160dk I want to send SMS and receive the data from UART simultaneously. UART needs 3V VDD supply and for Sim card it is 1.8V. So how this condition...