I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I use the SPIM to access a nand flash memory device. There are times, when I need to "free" the SPI bus allocated by the nRF52840, so that another CPU can access the memory...
I have been closely following this thread ( https://devzone.nordicsemi.com/f/nordic-q-a/52689/nrf9160-lte-sensor-gateway-on-thingy-91/217018 ) to provide support for the LTE...
Hello all,
I am using the NRF52810 board with SDK 14.2
I wanted to convert pca10040 to pca10040e file of buttonless dfu and secure bootloader .
I have gone through this...
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
Hi all,
I noticed an issue on the last release of the NRF Connect mobile app at least on Adroid devices.
It seems that every time I am trying to make a secure DFU (buttonless...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
Hi Nordic Forum! I'm currently developing a CLI controlled BLE scanner using the nRF52840 Dongle. Essentially I brought over the CLI example and adapted it to the a central...
Hi
it looks like the Publication Retransmit Count and Interval states default to 1 time and 100ms respectively. Is there a reason these defaults apply? I don't think it...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available. After a few minutes it sometimes changes...
I would like to program the 52840 with the HCI_UART sample to use it for Bluetooth scanning. I did this and lost the USB serial out. I now understand that on the Thingy91...
Hello,
I am evaluating the nRF52840-DK. I just want to play around with Nordic for awhile to determine if I want to port my current project which is written in C++ for Teensy...
I want to run various applications in some cases
what I want is :
In general, it runs own application.
When external memory(SD card, USB, EEPROM, etc... something...
Hello All,
I have developed advertising init in 14.2 sdk (in segger ide).
(working on nrf52810 board)
I wanted to migrate same functionality to 15.3 sdk so how i can...
