Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
I'm experimenting with the USB MSC example (SDK 15.3) on my nRF52840 DK. It seems to work well in the polling mode as delivered. However, when I try to run in interrupt mode...
I have a serial port set upp with the serial port library like this:
#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART...
Hello,
I am trying to get started with the 9160-DK. So far it does not seem similar to the 52840 so I decided to take to the "Getting Started Assistant" within nRF Connect...
Hi, I'm using nrf52832 and SDK15.3. And I'm using the ble_app_uart example. The device will go to sleep mode if there is no connection for 3 mins.
My questions are:
1...
I'm calling sd_ble_gap_adv_start after a connection disconnects to start advertising again and it's returning err_code 12... which is NRF_ERROR_DATA_SIZE. However, the documentation...
Hello,
I am currently working on a project that involves the host device to send configurations parameters over to the device. I was hoping the connection between in device...
Hello All,
We working on OTA features with nRF52810 using sdk16.0 . When we are trying to upload the firmware zip format through mobile its giving error "upload failed:Insufficient...
Hi,
I am new at mesh .I use SDK UART coexistence example to test, and I can scan Ble uart demo by nrf Connect APP. But I can't scan Mesh node by nrf Mesh APP. I've been...
I am trying to program the Nordic nRF51822 MDBT40 Series module to communicate to an STM32 processor chip. The way I understand the procedure is as follows:
First, I must...
I want to use mbed TLS backend in BLE stack.
For example, BLE controller will use AES(hardware accelerator, I think) to gennerate link key and encrypt.
I know that SoftDevice...
I am trying to step through the code of an example of the nRF5_SDK_16.0.0 on the nRF52840 board.
I downloaded the latest version of Segger Embedded Studio (v4.30c) and I...
Hi,
Working with hx711 library and want to add some function for taring. I have a problem that when i run my simple taring function, the function returns 0, but it should...
