Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I'm new to nRF52 and the SDK, trying a few things to learn, so might be missing something obvious, but I've been looking at this apparent issue for a few days now. ...
I've based my application on ble_peripheral ble_app_blinky example.
So I used the following Code as model:
with:
for update and notification of a charachteristic...
Hi Devzone!
I'm using LM5(BG96) LTE modem to publish the mqtt message.
When I test it at PC terminal, It works very well. There is no problem.
However, when I send...
Hello,
I am currently working on a project which is a pcb design with NRF52810 . To set the gatt services I need to increas ram size by changing NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
How can I modify the number of resends when Coap uses OT_COAP_TYPE_CONFIRMABLE, because I don't want to wait too long to get OT_ERROR_RESPONSE_TIMEOUT，
SDKs do have docs in markdown format. What is the recommended tool to be able to access all the features?
Tried MarkdownPad2, but it fails for example on @anchor tag.
...
Hello,
I have a problem statement in which I have to generate a file for data that is received from UART communication and want to send it to the mobile application whenever...
Hello guys,
For last couples of Days, we were trying to connect with IBasis NB-IOT Network with nRF9160 DK.
But not able to connect it .Please see below Snap Short for...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to send packet with different...
Hi,
In our project we are using the adc pin (p02) for batttery level measurement.
The analog dc signal from the battery is connected to p02 pin after the voltage is...
Hello,
Our peripheral device has no keyboard and no display.
Yet we would still like to have the most secured way of communication.
For our application, we don't like...
Apologies for the newbie question. Does this BLE Module need a separate antenna to be purchased? Or are you supposed to design your own with PCB traces? Some BLE modules have...
I want to avoid the soldering of the inside (Becoz of production isse) pins that's why I'm using all the outer pins of the ic. But the problem is RESET pin is inside so can...
Hello,
I am using UART_1 in my program to comminicate with other sensor. So the data is read from UART_1 and print to UART_0. Now I want to communicate with other sensor...
Hi, I am using BMD301 chip on my custom board which schematic i have shown below,I need to enable UART as well as nrf_log in my application. For this I am using SDK 15.3 PCA10040...
