Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
hi,
nrf52840 BGA footprint P0.22 config as UART0 RX mode, don't receive any data, but config as other pin P1.06, work normally.
and I also test QFN footprint with nrf52840...
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345). I red a lot of documents and tech support like these links but couldn't find my problem...
I have another MCU on the same board as the Nordic 52832. The firmware update image for the MCU is about 50kb in size, so instead of adding a parallel DFU for the MCU through...
So currently I am using a 5 second repeated timer to run all my operations but there is a draw back to this that the max accuracy I can achieve is of 5 sec, like if I want...
Hello!
I have 18-bit sensors with SPI and I2C , which I intend to use in a wireless array.
I need to choose equipment and topology (star, scanning mode?), enabling data...
We had a custom board made with the nrf9160 and I noticed I was having trouble communicating with the sim card on my board.
We have been testing i2c, spi, number of peripherals...
I am trying to run the hci_uart sample on my 9160 DK but I am facing problems uploading the code. I am able to run the AT client and Asset tracker just fine. As soon as I...
I've been attempting to optimize my scan and connection intervals in order to maintain the highest percentage of time scanning while maintaining connections, following the...
Hi,
I am developing a Linux PC application (central) connecting with nrf52840 dongle with s140 v7 flashed on it (for long range support). I am using pc-ble-driver v4.1.1...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
I have 3 devices that can communicate via UART: 1) nRF52840-DK (PCA10056) 2) FTDI (set to 5v logic) 3) BLE HM-19
I'm using the example in ./nRF5_SDK_16/nRF5SDK160098a08e2...
Hi,
In gps sample, the prj.conf file is:
And I can use Putty or Serial.app (on my Mac) to view the output
In our application the prj.conf file is the following:
...
nrfjprog is reporting "Cannot connect to J-Link." while trying to erase on MacOS Catalina
Board used to work properly, but attempting to re-connect after a wipe of my MacBook...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
