I have modified the NUS-CDC application for the Dongle so that I can now scan, report available Peripherals, and connect to a specific one. I need to be able to cleanly disconnect...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if we can use one Ignion antenna, shared for the LTE and GPS.
On the original...
I'm working on an nRF device (S112 SoftDevice) that acts as a connectable peripheral to an iOs central. The application only has data to transfer every 5 minutes, so I'm trying...
I was wondering how I can update my current code (see below) to reuse a single socket for multiple HTTPS requests, rather than opening and closing a socket for each HTTPS...
Hi,
Our team is interested in WiFi location service in Cloud Services.
https://www.nordicsemi.com/Products/Cloud-services/Location-Services
However, under the WiFi...
I'm having compilation error, and got a couple of errors similar to the examples below:
Error[Li005]: no definition for "sha256_desc" [referenced from C:\Users\..........
I need some parameters of the BLE s140 stack for my project.
Including duration of an advertisement event (beacon) and the maximum random slack for an advertisement.
I...
I've recently upgraded my IDE to use Crossworks v3.6.2 which uses a GCC ARM Embedded 4.9-2015-q3-update compiler. it has by default many of the code clean up featues turned...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
i need to disable RX when data was transmit and enable RX again when data transmit complete.
i tried :
NRF_UART0->TASKS_STOPRX = 1;
NRF_UART0->TASKS_STARTRX=1;
NRF_UART0...
Hello Everyone,
Is there any example code is available which supports DFU in central mode for nRF51 devices?
Any help will be appreciated.
Thanks
Regards,
...
When I change ATT_MTU size and add the following code:
#define CONN_CFG_TAG 1
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg));
ble_cfg.conn_cfg...
How do you do
Now use the Nordic nor51822 \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this routine plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples...
Hello,
Am working on NRF52 interface via SPI to Micron N25Q flash .
Am able to identify flash by reading chip identification correctly and after this to test memory writing...
We are a small R&D team and we are currently developing a medical wearable. We are using nrf52832 and we are generating approximately 54kbps (6.75kBps). I 'd like to ask if...
Hi!
After reading few posts about spi slave/master issues... I'm also challenging with one of them. I have following setup nrf51822, s130 2.0.1 and sdk 12.3.0… nrf51 (spi...
I am working on OTA DFU about nRF52810.
My refernece project are ble_app_uart\pca10040\s132 and bootloader_secure_ble\pca10040
I find that the RAM start address between...
Hello im trying to create a single master connected to multiple slave to make synchronous movement for my robotic arm project but im not entirely sure which Bluetooth to consider...
Hi,
I am running the BLE DFU example. I am able to perform the DFU OTA implementation successfully. The problem I am facing is that, once the application has been updated...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
