Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
I'm having compilation error, and got a couple of errors similar to the examples below:
Error[Li005]: no definition for "sha256_desc" [referenced from C:\Users\..........
I need some parameters of the BLE s140 stack for my project.
Including duration of an advertisement event (beacon) and the maximum random slack for an advertisement.
I...
I've recently upgraded my IDE to use Crossworks v3.6.2 which uses a GCC ARM Embedded 4.9-2015-q3-update compiler. it has by default many of the code clean up featues turned...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
i need to disable RX when data was transmit and enable RX again when data transmit complete.
i tried :
NRF_UART0->TASKS_STOPRX = 1;
NRF_UART0->TASKS_STARTRX=1;
NRF_UART0...
Hello Everyone,
Is there any example code is available which supports DFU in central mode for nRF51 devices?
Any help will be appreciated.
Thanks
Regards,
...
When I change ATT_MTU size and add the following code:
#define CONN_CFG_TAG 1
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg));
ble_cfg.conn_cfg...
How do you do
Now use the Nordic nor51822 \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this routine plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples...
Hello,
Am working on NRF52 interface via SPI to Micron N25Q flash .
Am able to identify flash by reading chip identification correctly and after this to test memory writing...
We are a small R&D team and we are currently developing a medical wearable. We are using nrf52832 and we are generating approximately 54kbps (6.75kBps). I 'd like to ask if...
Hi!
After reading few posts about spi slave/master issues... I'm also challenging with one of them. I have following setup nrf51822, s130 2.0.1 and sdk 12.3.0… nrf51 (spi...
I am working on OTA DFU about nRF52810.
My refernece project are ble_app_uart\pca10040\s132 and bootloader_secure_ble\pca10040
I find that the RAM start address between...
Hello im trying to create a single master connected to multiple slave to make synchronous movement for my robotic arm project but im not entirely sure which Bluetooth to consider...
Hi,
I am running the BLE DFU example. I am able to perform the DFU OTA implementation successfully. The problem I am facing is that, once the application has been updated...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
