Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Thanks for your help עוטד. I want to use BLE / beacon technology in order to track items that pass-by in high-speed and close proximity (0.5m). This means I only have a few...
Hi,
I am using ble_app_hrs_c as the base for central. I have included 5 characteristics in the peripheral and central side. How to make ble_nus_c_rx_notif_enable() to notify...
ble_gap.h Hi,
At the moment, when a link loss is detected (in a connected mode), it takes around 3 seconds for it to be identified (with DISCONNECTED event). Is there a way...
Hi,
We are using system-off mode to save power in our device which uses nrf51822 chip. Our application requires regular wake-ups using RTC interrupts.
But the wake up...
Hello!
I know that nrf51822 beacon advertising packet consists of the following seven data fields:
Vendor ID
Service
Data payload size in bytes
UUID – manufacturer...
I would like to develop a BLE keyboard using nRF52832.
If you know the example source code, please let me know.
And can USB BLE Dongle for Desk-Top PC use the following...
Hi team,
I am trying to figure out how mesh network works. I do experiment with nrf52832 develop board and nrf5_SDK_for_Mesh_v0.9.2-Alpha. After I flashed light_control_server...
I have an app that requires BLE stack to be re-initialized, however it seems that if you run
ble_dfu_init();
more than once, it crashes
Upon further inspection...
Hi all,
I'm working with the nRF52 and I'm trying to run the heart rate sensor example from SDK version 13.1.0 using Crossworks as my IDE. I can compile and run the program...
Hi,
The below results indicate the nRF Connect app requires a handshake even when scanning without connecting. Is this true?
I am using the android 'nRF Connnect' app...
Are there any known issues with the nRF USB on the new chip or dev kit? I bought a dev kit to test out the USB functionality, but was unable to get any programs working. No...
Hello!
I am studying with nrf 51822 eval kit.
I wanted to ask you something about data type of nrf51822.
For the iBeacon model, it needs 31 bytes. 4 bytes of them...
Problem: nrf_crypto_sign() fails with NRF_ERROR_INTERNAL. Observed in SDK 12.3.0 on NRF51422. This probably applies to SDK 14.0 when using micro-ecc backend, as the root cause...
