Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
I am developping NUS server(Peripheral) on Android. Central is ble_app_uart_c on nRF52832.
In this case, service discovery cannot be completed.
According to the console...
Hi. I am new with KEIL MDK and Nordic and ARM .....
I will create an MIDI BLE, but maybe anybody has an working Example for this?
Or what for an Example i can modify?
...
Hello, when I try to compile old working projects in SDK 11.0 with both Device Family Pack 8.5.0 and 8.11.1 (which I am using for SDK 13), I am running into the following...
Hello,
some time ago I was struggling with interfacing an I2S microphone with the nRF52832. That remained unsuccessful. My conclusion back then was that the selected I2S...
Hello, i use ibeacon example, this is the reader advertising packet, he has 31 byte long:
0201041AFF590002150112233445566778899AABBCCDDEEFAB010200FFC300
in this packet...
(/attachment/fad3a1e781331c528a9db48ec177b9b7)Hi there! i need help. I am using NRF52Dk with Bluetooth developmebt studio.
I set up my custom service in BDS an then imported...
