Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
What I have to do if I met this ? I round length to fit (len+4-(len % 4)). Is it right ?
if (!(IS_WORD_SIZED(m_start_packet.sd_image_size) &&
IS_WORD_SIZED(m_start_packet...
Hello,
We have problem BLE connecting to the nRF52832, if we use the method gap_init(), the "better" smartphones can connect(those who support BT 4.2). If we skip the gatt_init...
Hi,
I'm trying to program an external NRF52832 board with the NRF52-DK, per the instructions in this post .
Programming works fine, but the code doesn't execute after...
Hi,
I'm trying to do DFU in my app, I almost complete it, I met a problem that my app flashed back when I sent 04 to the device.According to the DFU doc,after uploading firmware...
Hi,
I'm using the ADC of nRF52832 on nRF5 SDK V12.2. The setting as attachment. I found that it just do sample one time. But I have use timer to call nrf_drv_saadc_sample...
The scenario like this:
A is BLE peripheral with firmware (ble_app_uart under nRF_SDK_13.0.0_04a0bfd), if no filter,any central can cenncet to it, but I just want B can cennect...
Dear all,
Help please,
I'm evaluating ble_app_uart (Central/Peripheral) but I don't understand how to disable the echo I have on the RTT USB VCP
When I send data from...
I am using 3 nrf52 DKs with S132 and SDK13 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and added the relevant...
Hello! I try to use three modules with chip nRF24L01 to syncronize two slave devices by one master device without wires. Required accuracy is about 10 nanoseconds. My idea...
We have an external interrupt every 4ms that collects one 24-bit sample from an analog front end via SPI. After Collecting 6 samples (18 bytes) we send a notification with...
