I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
I'm trying to minimize current consumption on my BLE peripheral and I wanted to know what advertising data is required. I have a custom service with a 128-bit UUID but do...
Hello!
I am using a keyboard (4x3) and the rows are configured as input PD and columns as output set, after a successful interrupt , the columns and the rows shift settings...
I am using nRF8001 bluetooth ble for my project. I would like to get the RSSI value as a reference value in my firmware. Is there any way that I can get the RSSI value from...
Hello,
I'm using the following (nRF51822-Beacon): www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit
I would like to use the beacon for beacon-to-becaon and...
I am calling the spi_master_send_recv in a ISR from a GPIO using app_gpiote.c It causes a hardfault on APP_ERROR_CHECK(sd_nvic_DisableIRQ(p_spi_instance->irq_type)); Otherswise...
Hi,
The nRF Toolbox app on iOS crashes when opening user added files in the DFU. These files are added to the app via iTunes. The version of the nRF Toolbox is 1.7 which...
Hi,
We're producing a custom board based on the nrf51822 and would like to add a USB Serial chip.
The current contenders are:
a) FTDI 232R
b) ATmega8U2 ( www.arduino...
As the picture shows, I saw this softdevice_hex option available.
The error says, "require nRF_SoftDevice S310_Hex".
But where to this missing component.
My development...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
Are there any pins that I can NOT use for SPI on the nRF51822? I'm not seeing any notes in the latest documentation but would like to make extra sure before I spin a board...
