Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi
I am using sd_ble_gattc_primary_services_discover(conn_handle,0x0001,NULL) to discover primary services on a GATT server. After the first call to this function, I get...
In nRF51 PS, I read typical/max time for AES ECB are respectively 8.5 and 17µs.
What would be those values for the whole AES-CCM operation (ie including MIC computation)...
Hello,
I'm working on a software we've made starting from the "ble_app_uart_s132_pca10040.uvprojx" source code. My "main" (procedure fct) is in the for (;;) of the void...
Hi,
A couple new fixes in listed files to supress gcc errors when -flto enabled.
hardfault_handler_gcc.c
port.c
Patches are in answer below.
Regards,...
I´ve read that the command "lib_aci_close_remote_pipe" is not available on the chip NRF8001 build code C. I need execute this command to solve a bug in the ANCS service. If...
Hi
I have setup and configured Eclipse using the tutorial and all seems to be good, except, I cant flash the binary to the chip. Here is my error when calling flash:
...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
We are using your nRF24l01+ chip in one of our products. we are using 1 nRF as receiver and 5 nRF's as transmitters.
While trying to use the chip with multiciever configuration...
Using SDK13 - I would like to use the fds/fstorage libraries, but I'm told that "The experimental label is due to lacking test coverage for the two modules". here
At the...
Hi,
I've been suffering with detection of writing to cccd to enable notifications. The S132 (nRF5_SDK_13.0.0_04a0bfd + s132_nrf52_4.0.2_softdevice) never fires BLE_GATTS_EVT_WRITE...
Hello, I'm migrating a project from nrf51 to nrf52, and there is this function:
uint32_t dfu_init(void)
{
m_cmd_handler = *((bl_if_cmd_handler_t*) (0x20000000 + ((uint32_t...
Hi,I use demo project in
nRF5_SDK_12.1.0_0d23e2a\examples\peripheral\saadc\pca10040\blank\arm5_no_packs\saadc_pca10040.uvprojx.
I made the following changes:
1.add...
Hi all,
what is the most correct way to delete the bonding information when the client and peripheral are connect.
Delete_peers
Wait the QUEUE_EVENT_PEER_DELETE_SUCCESSED...
Hi,
I have an nRF52832 sending data to a central device. At the central side I am testing two tablets (separately). One is a Samsung Galaxy Tab A 2016 10" and another one...
