I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
I was following instructions from this and this post, but I'm not yet able to build with the following combination: CMakePresets.json + west + sysbuild.
I'm using this west...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Dear Onomondo Support Team,
I am currently experiencing an issue with my Onomondo SIM card — it is unable to register on the network when used with the nRF9151 DK board...
The end of memory bss is @ 0x20002DAC (11692B).
The start of the heap is @ 0x20002DB0 with a size of 2560B.
The heap ends at 0x200037B0.
The stack works back from the end...
Hi,
I intend to buy the NRF51822 beacon to use it to transmit data from an SPI-linked sensor. Is this feasible? (It seems so, but I just want to make sure). Also, will I...
Yesterday was the nrf Beacon application for Andriod Studio released. I added the project DFU library to the same folder as described. But I get an error:
Gradle 'Android...
Hello! I want to try IPV6 for nrf51822. I have a few questions:
How many connections can be provided by the one device?
Can we broadcast messages between devices...
Hi,
I'm developing BLE functions using nRF51822 on top of the Android Kitkat applied device. I cannot find android bluetooth HAL source code that Nordic provides. Is there...
In my application I have a custom board with a single LED. While advertising the LED blinks at 1Hz and when connected the LED goes solid. However while testing with a proven...
I'm creating an application based on the s110 SoftDevice found in nRF51_SDK_8.0.0_5fc2c3a. I'm new to the SoftDevice framework so I've probably made an error somewhere but...
Is the GPIO pull down/up asserted on the 'inside' of the input disconnect switch or at the input/output pad? The diagrams would indicated that it is on the 'inside' of the...
This is function definition:
static uint32_t battery_level_char_add(ble_bas_t * p_bas, const ble_bas_init_t * p_bas_init)
This is declaration of the automatic variable...
Before starting advertising, we want to write some configuration information to NVM. In order to write to NVM, we first call sd_flash_page_erase and wait for the response...
I just posted a package of simple tools I wrote for OSX over on Sourceforge . The main app is a Cocoa app which lets you choose code, softdevice and bootloader (last two optional...
I Saw iBeacon Packet in the website
(d6 be 89 8e) Access Address for Advertising
(40 24) Header
(05 a2 17 6e 3d 71) Mac address
(02 01 1a 1a ff 4c 00 02 15 e2 c5 6d...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
What happened to NRF_FICR_Type.INFO and FICR_INFO_Type in nrf51.h?
This was in ./components/drivers_nrf/hal/nrf51.h in nRF51_SDK_7.1.0_372d17a
but is missing from ....
