I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
For programming the nrf52832's BLE capabilities the only option that can be used is the s132 soft device right?
According to the latest specification, the maximum throughput...
Greetings,
I have an application where the DFU of a NRF52 is performed by another microcontroller via a serial port. Once the DFU is complete, the microcontroller turns...
Hi everyone!
I'm wondering about why SoftDevice stays idle (in terms of radio operation) so "long"
("t ScanReserved" = 760 us) after channel changes during scanning? Despite...
Hi,
I'm trying to do a rough calculation of current consumption for the nRF52840 chip.
The unit should sample 6 times an hour by using I2C to acquire samples from a...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Hi,
We are designed our own Beacon PCB based on nRF51822 Beacon Kit...We followed board size,PCB Antenna Trace width and GND Clearance as per Beacon kit...The difference...
As I understand it only the largest physical chip, 7x7mm nrf52840 , supports Bluetooth 5.0 long range. Is this correct?
It seems as if Nordic Semiconductor is abandoning...
Hi,
i have assigned RAM address as:
#define RAM_MEMORY_TEST_ADDRESS (0x20002BD8)
uint8_t * p_ram_test = (uint8_t *)RAM_MEMORY_TEST_ADDRESS;
to this p_ram_test i...
Hi,
In the Thread API under the Command Line Interface section, there are the following functions:
void otCliConsoleInit(otInstance *aInstance, otCliConsoleOutputCallback...
Makefile (/attachment/ca6852bdad7b5e54aaa4ce4388c4c410)Please find my code attached!!!
I have changed the makefile and the SDK config file accordingly! but the error remains...
Why can not read twi data ? at nrf52832 chip....
but Read well in Arduino....
twi interfacing with RTC DS1307....
please give me some hint.....
nrf_drv_config...
i would like to print register values of an external sensor on my screen using UART! I'm reading and writing into those registers using SPI! Printing a normal message using...
Im working on 14.0 and s132 and work inside ble_uart code...i was add rtc inside that code sucsessfully but now.. when device goes to sleep so rtc interrupt handler function...
I have just changed line 74 of nrf_drv_uart.h file as
#define UART1_ENABLED 1
instead of
#define UART1_ENABLED 0
and the example gives an error. Please find...
So i am utilizing SPI and i got it to work, however for some absurd reason after removing the segger_print statement below from before the while loop the spi would stop functioning...
