Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
Hello.
I am trying to turn off ACK in the example "esb_ptx". I have tried this in both SDK 12.2 and 14.0.
I try to turn off ACK like this:
static nrf_esb_payload_t...
Hi,
I am trying to establish a border router in my test Thread system (a part of infocenter.nordicsemi.com/index.jsp . I have the required Raspberry Pi 3B, but it is driving...
I'm using the 1.0.1 nRF Sniffer and 1.10.10 Wireshark on Windows 10 64bit. The firmware 1.0.1 is programmed to nRF51822 dongle using Jlink 6.12a. The exe works fine when no...
Hello everyone,
I want to integrate NFC to one of my projects and I am having a problem with the value of some of the capacitors.
I am looking into using the nRF52832. ...
Where can I download the example project that can be imported into Eclipse?
Tutorial: devzone.nordicsemi.com/.../
Broken link: ble_app_hrs
When I follow the link...
can't program nrf52832ciaa
I can connect the core through segger commander
I can erase the chip after push the download bottom in the keil 5 ,and erase the chip...
I have an nRF5- DK and I'm following this tutorial . I loaded the softdevice, I can compile, I can load the flash, I can see the output in Termite, I can change the code to...
Hello,
I have an NRF51822 custom board. I am trying to flash the code under
C:\Users\Home\Desktop\nrf51\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Greetings -
The (custom) device I'm working on has multiple possible serial interfaces. I thought "Hey, I've written entire operating systems before, I should just intercept...
Hi all,
i need to write in flash, and i try to use the example flash write of sdk. It works correctly but when i put it in my code, the writing register ( NRF_NVMC->CONFIG...
Hi!
I'm developing Thread mesh using nrf52840 with COAP communication. I would like to set a longer timeout and more retransmission tries in COAP. I saw this parameters in...
I am trying to use one of the example from NRF5 IoT SDK with RPi3 (kernel 4.9.41-v7+) but keep getting "permission denied" when execute command below:
echo "connect 00...
Hello
I have setup my Eclipse(neon3) on Linux following the instructions in devzone.nordicsemi.com/.../7
I cant compile and flash the image. But cant breakpoint.
I...
