Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
Hallo,
I try to use the s310 timeslot API. I open a "session" and then request a timeslot:
check( sd_radio_session_open( nrf_radio_signal_callback ) );
request_radio_slot...
I am trying to implement the pulse counting mentioned in a previous post of the same name, but the code is eluding me. I am using the heart rate service example with new code...
Hello,
I want to implement a firmware update over ble for my application and the SoftDevice 130. Which would be the correct boatloader.hex that I should use? I am working...
Hi,
I am using softdevice-7 and SDK 6.1 for our application.
If I connect using a passkey, first 「BLE_GAP_EVT_SEC_PARAMS_REQUEST」 event occurs, then the 「BLE_GAP_EVT_PASSKEY_DISPLAY...
I have a mature design with several hundred units built using QFAAE0 silicon. Code works. Hardware works. FCC is happy.
I'm considering migration to V3 silicon and maybe...
Hi....
I have PCA10028 DK and i want to make a profile that works both as central and peripheral. As a part of this i tried running S130 demo app found in S130_softdevice...
I need to remember the CCCD's of some service, e.g. service changed. A CCCD is according to spec 2 bytes long. The method to do this is by using sd_ble_gatts_sys_attr_get...
Not sure why but my time is only firing at 250Hz with the prescaler set to 0. Not sure why. Shouldn't it be going at 16Mhz at these settings? (Running on the PCA10028 Board...
Hi,
I am using device as ble-Peripheral SDK nRF51_SDK_7.2.0_cf547b5 and softdevice
version :s110_nrf51822_7.1.0_softdevice.
problem : I am receiving data on Nordic...
I'm trying to use the internal temperature sensor of the nRF51 to know the die temperature. Its accuracy is specced as +/- 4 degC, even +/- 8 degC at the extremes. Does anyone...
Hello,
I am trying to control the smart phone function while making my device as HID keyboard, but It seems that the soft keyboard (smart phone on screen keyboard) clashing...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
