Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I noticed the various examples as well as the ble_advertising component all check for pending flash operations and will not start advertising until they are all...
hi guys,
im developing a program to interface accelerometer MMA8452 with nrf51822.so if accelerometer is in peripheral device,how do i send the x,y,z co-ordinates from peripheral...
Hi everybody, i am working with a nrf51822. S110 with sdk6.1 IDE:keil
I want to do FLASH Erase while in a connection.
I have read this page devzone.nordicsemi.com/......
On initialization of the bsp, I get ERROR 4 (NRF_ERROR_NO_MEM) when I define LOCATION.
Why is this? Because it seems rather weird there's no more memory at that point in...
Hi all,
When I start the bootloader using ble_dfu service as-is in my application I get no ble events in the bootloader. When I call the bootloader from the main loop it...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
I am trying to do OTA DFU on nRF51-DK from a BLE dongle (CSR 4.0) and gatttool from BlueZ. The image is compiled from blinky_s110_pca10028 example ( blinky_s110_pca10028.hex...
Hi
I want to program the S120 softdevice over an mbed HRM1017 ([link text] that uses nrf51822. I can program only with CMSIS-DAP or drag and drop over the drive. I am using...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
