Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hello,
I would like to know how I can check whether the SAADC is enabled or nor on my application. I am disabling the SAADC with nrf_drv_saadc_uninit(); after configuring...
I'm using the latest SDK (14.1) and have got a working COAP server running over BLE on a nRF52DK, and can exercise the service from my Ubuntu desktop without any problem....
Hai team,
Iam using the ble_app_beacon example program.
I found power profiling calculation on this link devzone.nordicsemi.com/.../ .
i calculated power consumption...
Hello,
I installed the new nrfjprog but it fails to write my nrf52 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with ERROR: argument...
Hello,i want to get the mac address by sd_ble_gap_address_get().There is a error message as fellow: Undefined symbol sd_ble_gap_address_get(referred from main.o). Where is...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
Hi,
I get following error when i try to compile nRF5_IoT_SDK_v0.9.x for target nrf52822
compiling x509_csr.c...
assembling arm_startup_nrf51.s...
(13): error: A1517E...
I'm working with LEDs in a ble example
I'm calling ble_notification_init() and activate the LED in the callback handler.
I get sd_nvic_ClearPendingIRQ, sd_nvic_SetPriority...
Is there a way to get the RSSI value of a message using the standard functions within the sdk for mesh. I am currently using a modified version of the simple_on_off client...
