Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
I'm having trouble adjusting ram start setting using the new SES projects from latest SDK14.1.0
I have tried the project linker section placement macros settings of
...
Hello, is it possible to use a wire antenna with nRF52832?
I have read that only PCB or chip antennas are used, so I expect the answer to be no, just wanted to confirm...
Hi Nordic Engineers!
I read the description of new SD s140 v6 and find a lot of good features.
A question 1, is this the next version that will be supported in the future...
HI，all
In normal circumstances, ios phone paired and connected to my 52832 device, when they are disconnected, ios phone can automatically reconnect the ble device. But sometimes...
Hello ,
I want to use the Button with Height level to trigger.The default is Down level to trigger.What should i do for that ? I try to set BUTTON_PULL NRF_GPIO_PIN_PULLDOWN...
Hi,
I have just added over the mesh bootloader updates for my mesh and I am curious about the MBR parameter page. I want to use that page as a swap page in my application...
I set the NRF_LOG_BACKEND_RTT_ENABLED 1 and NRF_LOG_ENABLED 1 in the bootloader and application.
After a reset, the application gets stuck in the bootloader
Or maybe (bl...
