Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
I am using nRF51822 to generate 3K HZ PWM signal for a buzzer.
I read other people's question and try it.But as far i can't solve this issue.Please help.
At first i use...
Hello,
I just ordered a shiny new nRF Beacon from Mouser. The beacon is version 1.1.0 advertising "DfuTarg", so I am attempting to flash the application file that comes...
Enlight of the increase in 8.0 SD size, I am concerned that my application size may soon grow too large to utilize Dual Bank DFU. I know the actual size of the .Hex files...
修改Device_Name.jpg
After programming, the device name cannot be changed.
Is there any solution that can achieve?
I know that I can change the paramter from the function...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
The Master Control Panel will be able to keep the connection for hours and hours.
But when I am using the iPhone 6 to do the test, after connected, it will also be disconnected...
Hello
I've been having some strange problems with my SPI and TWI bus. In my setup, I'm using SPI0 and TWI1. I noticed that, even though I'm not using it, that SPI1 was...
This seems to be a common problem after searching in this forum. In my case, I need to read from an I2C slave and send the data out in BLE. I have made it work without SoftDevice...
Hello!
In my application, I have to receive UART signals from another device. The problem is the signal comes inverted so the nrf51422 can't handle it. I thought in 2 possibilities...
In spi_master.h SPI_DEFAULT_TX_BYTE is define as 0x00.
This value will be used when sending dummy clocks, or just reading from SPI slave, or writing length is less than the...
Is there a migration guide from 8.0.0 to 8.1.0? A lot has changed in GPIOTE and I can't make sense of it.
For example, should I be linking against app_gpiote.c , nrf_drv_gpiote...
