I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I want to give the application priority to run when it run with the bootloader.
I'm using PCA10028 and SDK12.
When the bootloader is uploaded with the softdevice, the...
Hi, I've read through partially of the "getting started" docs, and I'm still having questions about these issues:
Will there be one dedicated provisioner interfacing...
I was writing 3 character to ble device .but I got below error and ble device got disconnected. LED lights got off...
[CoreBluetooth] API MISUSE: <CBPeripheral: 0x1572b660...
Hi, when doing wired uart-BLE combination and increasing the traffic in the uart comms and BLE comms, at some unpredictable stage, the program flow goes to 0xFFFFFFFE. Any...
Hello,
I am trying to run the ble_app_uart_c example that is part of the nRF5_SDK_13.1.0_7ca7556 on a custom board with nRF52832 using IAR. Hardware seems healthy, I succeeded...
Hi all,
Could you please point me at the tutorial I missed... I am looking to adapt the title project to a custom project. I've run the sample and it advertises and shows...
Hi all
we are working on nrf52832 for our project.
not sure if there is guidelines for pcb antenna.
like limit on number of devices or any other certification we need...
Hi,
I'm using a nrf51 custom board (IC no. N51822QFAAH0) with Softdevice S130 v2.0.0 and SDK_11.
After connecting it with nrf Connect Android App, the device gets disconnected...
Hi:
I'm running S132 SoftDevice for the nRF52832 and am interested in configuring the nRF52832 (slave) to achieve connection intervals from 2 to 16 secs.
Thanks,
JP
On a custom board with an nRF52832 communicating over UART with another microcontroller with no flow control capability.
SDK 13.0.0-1.alpha with an S132SD.
I have some...
Hello everyone,
Thanks in advance for your patience in reading this long message.
I have been having problems with UART over USB on PCA10040 boards for almost four months...
In order to learn how to use the RTC0 to handle an event every second, I am debugging the rtc SDK example.
Expectation : The rtc example sets the time to check the counter...
I need to make sure that the receiver is active in an NRF52832 that I don't have good ability to do DTM commands on; there's a host processor that can do some DTM commands...
