Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
In my project, an android phone is needed to connect to two ble devices. All my ble devices are nrf51822. The android phone can connect to and receive data from every device...
Hi,
to investigate a timing problem in my Bluetooth stack, I've hard wired the Radio ADDRESS and END events to a GPIO pin using the PPI. The ADDRESS event is used to toggle...
Hi,
I'm developing a FW with a lot of services and characteristics. Since I added the ANCS service, I have the "NRF_ERROR_NO_MEM".
Configuration : NRF51822_XXAC / S130...
hello everyone,
i use nrf51822-QFAA(256kb flash,16kb ram).i want to use sdk12.3.
at first i can't build the project,after i install some tools, i can build it ok.
...
i am using nRF5_SDK_13.0.0-1.alpha_055eef3 s132_nrf52_5.0.0-1.alpha_softdevice and used examples\dfu\bootloader_secure\pca10040\ for secure DFu OTA .everytime i try i get...
What's the current consumption for a Timer on the nRF52832 when it's used in Counter mode? Do Timers require the 16MHz or 1MHz clock when configured for counter mode?
Hi Vidar,
I am planning to start devlopment on the nRF52 and I would like to use GCC ARM with Eclipse. After having read your post "Development with GCC and Eclipse" and...
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
Hello, I'm using this code(observer):
github.com/.../nRF51-multi-role-conn-observer-advertiser
SDK9.0.0
I try to add DFU function, now can enter dfu mode and iPhone6...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
I want to establish BLE connection and have a central device receive data from a peripheral device. I am using the Heart Rate Collector as an example and notice the main file...
Dear All :
Is it possible to creat a pwm with 1sec period?
Since the lowest frequency of the base clock is 125kHz，the top count of the pwm with 1sec period will be 125000...
Hi.
I havent found answer for - in my opinion - common question - how to temporarily change name of ble device on button press. As long as button isnt pressed - advertise...
