Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Has anyone had success with a J-link ARM v7 with the nRFgo studio (and nRF51822)? I've got one of the older nRFgo moterboard dev kits, and I've been doing well with the included...
Hello,
I am working on a product, which uses the nRF8001 as basis for the Bluetooth communication. The application offers two interfaces, a custom interface and a HID interface...
Hello,
I have a problem with Indicate Characteristic. When I try to send data using sd_ble_gatts_hvx() function, it always sends 20bytes from address 0x00. This is my code...
I am trying to run my program once per second using timer. The timer is initialized as follows:
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
I'm trying to figure out how the bonding works in the multilink demo. It seems like the central device only goes through the bonding if the peripheral has the multilink service...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
Do you have a BLE SOC chip that can behave as a master and a slave, and also has embedded stack so no host processor is needed. I am looking for a chip that can be used in...
hi,
Inorder to flash the softdevice to evaluation board PCA10024 , i tried using nrfgo studio as mentioned in the user guide.but the nrfgo studio does not show any board...
Dear all,
I am using SDK7.1 with S130 v0.5 alpha. Can I use the DFU example in the SDK6.1 to update my firmware in the chip(nRF51422)? If not, is there any alternative...
I am using S110-based peripheral device which is sending 20byte notifications. Application on my peripheral works fine (testing with MCP gives transfer rate about 15kB/s which...
Hi,
I was using nRF51DK with Keil uVision ver 5.14 and SDK 8.0.0. It worked okay yesterday and I tried HW peripheral as well as BLE peripheral.
But today it doesn't...
Is it possible to identify a device as a previously bonded peer based on the advertisement package and before establishing a connection?
I would like to be able to bond...
