Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi, I am using sdk 12.3.0 sd130v2. I have the hardfault_implementation.c included in the project. But I am not able to keep breakpoint anywhere in that file. I have made HARDFAULT_HANDLER_ENABLED...
I have initialized SPI0 master by this code:
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(0);
...
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;...
Recently I have been working with the serial bootloader from SDK 11. I can upload a softdevice, and supporting application using this bootloader without issue, as long as...
I started working on mesh 51 series ,
Points for which we need inputs
Data packet size for transmission
Process for association and address assigning during commissioning...
Hi,everyone
I am using S132 and SDK13 to set two peripheral links,now i want connect two centers using different connection parameters at the same time,for example,connect...
Hi,
Can the nRF52832 support higher data rates:
UART TX baud rate of more than 1Mbps, such as 3 Mbps without bitbanging.
TWI of 1MHz
any trick to get them...
Hi,
I recently purchased the NRF52 DK. I'm using the ble_uart_example for the SDK 11. I'm using the softdevice PCA10040.
I noticed the the SDK 11 includes the RTT c...
I want to use the nrf52840 with DCDC in high voltage mode to drive the circuite directly from a LI-ION battery.
Is there any reverse current protection built into the chip...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
