This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi Hung Bui,
I am working DFU now, all the thing's good for nFR52832, but in same way nFR52840 not work, I just wonder nFR52840 is ready for DFU?
Thanks.
JG
HI,
I want to turn off the broadcast timeout, but when I change the broadcast timeout macro to 0 when the program does not work，
Modify as follows：
#define APP_ADV_TIMEOUT_IN_SECONDS...
I'm attempting to use Peer Manager with my nRF52832 module as a peripheral with an Android 7.0 phone as the central device.
My program is a mix between the NUS example...
Dear Nordic,
I have built a board using nRF51422, and I've just manage to populate it and start it up.
I'm using a modified example (peripheral_lbs), and everything seems...
Hi, I have an Adafruit Feather52 board which is preloaded with a serial DFU bootloader and the S132 Softdevice, of which I also have the merged Hex file. I would just like...
Hi,
I am designing a custom PCB using the nRF51422 chip. I have a program that I developed on the nRF51-DK. The program reads the capacitance value of a proximity sensor...
Hi All,
i need some helps. I need a device that can connect with one phone only, so i have created a whitelist wih size of 1.
During the life of device the device can...
Hello, I'm pretty sure the new BLE 5 will come out soon and it will integrate the mesh. And if mesh needs to be done at a protocol level, it must be the softdevice.
So...
Hello iam using softdevice 110 and SDK 10.0.0, i have implimented dfu in my project, i want to update a region in EEPROM by calling pstorage_update() function before calling...
A while ago I asked this question devzone.nordicsemi.com/.../.
Yesterday I re-installed MDK 8.11 after a computer crash and I had IAR version 7.60.1 and version 8.11.2...
Hi,
I need to design a small nRF52 board On 24mm Dia 2-layer PCB, same like nRF51822 Bluetooth Smart Beacon Kit (nRF51822 Coin-Cell design). Please find the attached Schematics...
Hi everybody.
I encountered issues with the formentioned setup. In my project I'm using latest SDK 13.1, softdevice S132 v.4.0.2. I'm compiling the project with latest...
Hi to everybody,
I am working with a custom board based on the nrf52832, while trying to integrate to my existing application the DFU functionality I am having problems...
