Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
Is it possible to make pairing without the peer/device/bond manager? I am using SDK 12.3 on NRF51 and/or NRF52 and would like to get it to pair with a certain device...
Hi,
I'm using nRF52840 and S140 based on the ble_app_hrs_rscs_relay example. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu...
Within a buttonless DFU application should nrf_dfu_flash or fstorage be used to erase and write to flash?
SDK 13.0.0 - Soft device s132_nrf52_4.0.2_softdevice running on...
These messages below appeared when I built bootloader_dual_bank(sdk11) in the eclipse.
'Building target: bootloader_dual_bank_s130_sdk11.elf'
'Invoking: GNU ARM Cross...
I want to have blinky orange led,
0 mean on, 0x8000 is off, right? and why??
I have no idea what's 0x8000 mean!
so if I want have orange(full-R and half-G), how can...
I'm trying to debug my UWP Central app, which interacts with our device based on nRF52/s132. What I think I'm seeing with my packet sniffer (the nRF51 sniffer, incidentally...
I have set the
advdata.include_ble_device_address = true
in advertising_init function. However, the mac address data is not shown in mobile APP.
Is it due to the fact...
I would like to include multiple p_chunks in one record. How do I do this? I've only seen examples with one chunk per record, but fds_record_t.data has a field called number_chunks...
Hi, I am considering using nRF24L01 for a project, and I wanted to use one single transmitter to send data to various receivers (more than 6).
I have found some information...
plss, help me . i can flash other examble nomarlly . But when i tried to flash ble_app_uart to nrf52832 seem previous program still works and new program not flashed yet ...
Hello,
I'd like to store a large amount of data in flash and in a chosen area. As a start, I've chosen the area starting from 0x77000 and ending at 0x78000
Iv'e written...
I have been testing out with NRF52840 and verifying the data transmission using the NRFConnect app on my mobile. I am not sure what went wrong! It's no longer advertising...
Hi!
I have a small issue with one of my current project. I've built myself a custom board using the nrf51822QFAA. And I am using an stlink (on an stm32f4 discovery) instead...
Hi,I have tried to write some characters like device name for BLE device. When I called
Code:
grantPermissionCharacter?.service.peripheral.writeValue(data1, for: grantPermissionCharacter...
