Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys,
I want to ask if it is possible for a nrf51822 to connect to a Central ( my cell phone) without advertising. Let assume that my cell phone has nrf51822's MAC address...
Hi,
I am using st-link debugger with NRF51822 module.
I was trying to connect it openocd, but it failed. st-link is working with STM32 processor and able to flash through...
Hi,
I found a suspicious line of code.
SDK: nRF5 SDK 13.1.0 (7ca7556)
File: peer_data_storage.c
Function: pds_peer_data_read
At line number: 415
if ((*p_buf_len...
Hi,
I made a custom board with nrf51822 and custom antenna which works fine for examples which use SDK10 + SD110.
For my application it was recommended to use SDK12.3...
Hello,
i am working on a rotation counter, i am using adc and LPCOM with nrf52832 DK board.
but LPCOM code is not working.
static void lpcomp_event_handler(nrf_lpcomp_event_t...
Hello every one,
I'm using nrf51822, for some calculation, I have to use logarithm.
is there a possibility to directly use this function by nrf51822?
I already applied...
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I used the reference design file provided by Nordic (NRF51x22_qfax) but added the following...
I want to run the HID Mouse and Keyboard examples on nRF51 Dongle. How I can configure it first, to connect with my PC via Bluetooth and second, to configure the GPIOs act...
From document [Getting started with the nRF52840 Preview Development Kit]
( www.nordicsemi.com/.../Getting-started-with-the-nRF52840-Preview-Development-Kit)
we know that...
Hi,
I'm looking for a BLE device to work with an arduino and to speak with a smartphone.
The point is that the connection should be made by the user via the smartphone...
I am using nrf52 with sdk11. I have set the advertiser data as Manufacturer data in nrfConnect app in my android phone. So that whenever the data from my phone is advertised...
Hi.
I try run "ble_app_hids_mouse" example from nRF5_SDK_11.0.0 in nrf51422 (nrf51 dongle).
Previously i ran this example in nrf52 (nrf52 DK, s132 SoftDevice), and all worked...
Hello!
We use chip nrf52832(QFN-48) in our project and we wont to pass the PCB certification.
But we also want to use chip nrf52810(QFN-48) in another project, but with...
Hi ,
Please advise, what the Low Power option I have if I want to sample Two channels of analog input at the same time. The sample rate in every channel is 12K, 12Bit....
