I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
Hi all,
I am working on Temperature and Humidity(DHT11) with nrf52832, After advertising the Bluetooth i am calling the DHT11 sensor function in loop, few seconds it is...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
Hi,
I was trying to implement software UART for our product so I decided to use timer compare channels event connected to gpiote with interrupt. I want to toggle data line...
Hi,
Application: turning on/off a LED by toggling a GPIO pin using a timer and PPI. Important: the on-time of the LED must be very precise, i.e. the jitter must be minimal...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
