I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
In our application we use gazell. We also want to use the flash data storage which uses softdevice.
With gazell enabled, we cannot access flash.
What is the recommended...
Hardware: nRF52 DK
Example: ble_app_hrs
I have a problem with starting program using debugger. I starts debugging session and starts program using resume button, breakpoints...
I'm trying to configure SWO properly, specifically to get the output in Eclipse. The following code is used to initialise the SWO.
I have a snippet that outputs a string...
BLE is always running on Arduino Boards PROMO and PRIMO CORE
Even small example Sketches like Alarm Interrupt who doesnt use BLE functionality in the code enable the RADIO...
hi sitting and looking at the light demo example through and looking at where I do not quite understand what p_args is used to, so someone can explain that thanks: D
Hello Sir,
In last my custom nRF52832 PCB i have use 100nF capacitor mft part no: "C0402C104K4RACAUTO" but now it is nor available in digikey.
So please sir provide me...
Hi all,
Is it possible to get a softdevice which can do 2dBm output? Our device is very power critical, but we would like to have as much power as possible.
At 4 and 3dBm...
Hello, I'am working on the code of ios-nrf-beacon( github.com/.../IOS-nRF-Beacons).I found the code with Objective-C,but I'm working with swift,I want to know if there is...
What is the proper way to use the Queue Library and define a queue that can be used across multiple C files? I have the following code a my common header
NRF_QUEUE_DEF(uint8_t...
Hi all the Nordic friends and Team,
I would like to do a Batch OTA of one hundred devices right now... I'm on the NRF52 stack for my devices to be flashed. And I'm using...
I test SoftDevice V6.0.0 on nrf52832(BLENANO2) I run 1. sd_ble_gap_scan_start() 1000ms/100ms/10ms scan_window/scan_interval 2. sd_ble_gap_adv_start() 1000ms interval result...
When my mobile phone reads my characteristic, I would like the characteristic to be calculated at the same time, and not before. i.e. like a video game that does not render...
Hello Supporter,
I am Using NRF51822 QFAC .
My probleme after uploading DFU ,SOFTDEVICE AND APPLICATION .device always in DFU mode and also when try to upload new application...
Hello Supporter,
I have NRF51822 QFAC having 256kb ROM,32kb RAM.
now i want to upload all three things DFU,SOFTDEVICE,and APPLICATION .when i upload SOFTDEVICE and APPLUICATION...
Getting ready to go into production with our custom nRF52832 board, we need the board to start running our application immediately after being flashed. Using:
nrfjprog version...
