Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I'm trying to use slave latency to reduce current consumption of my device.
Connection parameters defined in `main.c`:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(15, UNIT_1_25_MS...
I have been using the pc-ble-driver Python bindings to implement a peripheral. I have extended BLEDriver to support sd_ble_gatts_* the functions. I now have a working peripheral...
Hi,
At the moment I generate 4 independent pwm signals, I would prefer to have 6 but this is not possible to my understanding due to the lack of GPIOTE [ ref1 , ref2 ...
Hi Folks,
I'm having trouble running the demo second time followed the steps mentioned http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk...
I am having trouble with nRF5 SDKv15. I am using the nRF52840 SoC. I have been looking at the example projects for both the RTC and TWI implementations for reference and cannot...
Hi,
We are developing a wireless sensor for research purpose using NRF52. I was always develop under Bluetooth 5.0 environments. The phone i am always using is Xiaomi MI...
I know the Nordic provides timeout parameter to control advertising parameters.
If I set the ble_adv_fast_timeout to 1s, my ble-central device scanned the advertisement...
I can use standard UUIDs and successfully add a Service and several characteristics, so I think the error message above is a red herring. When I attempt to create a custom...
Hi there,
I am trying to modify flashwrtire peripheral example code for uart bootloader,
- I have used flash read write softdevice functions (sd_flash_read/sd_flash_write...
I am trying to program a BMD-300 over a serial connection through the RigDFU bootloader. The module has been updated to the latest factory image.
I can compile the application...
Now I want to run the python scripts interactive_pyaci.py in Embedded system device, I want to know which version of Python Environment must be install in the Embedded device...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...