Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi,
I successfully installed and test pc-ble-driver with connectivity_2.0.1_115k2_with_s132_5.0.hex on PCA10040.
When I download ble_connectivity_s132_uart_pca10040.hex...
Android nRF Connect app DFU is flakey on my phone, a Motorola Droid Turbo w/Android 6.0.1. I tried with a Moto X and it worked fine, but on my Droid it rarely downloads successfully...
I'm using 52832/S132 V2/SDK11. For the test I only send notification to central just to see how many I can send in each interval. I keep calling sd_ble_gatts_hvx() until I...
Hi, I am having some issues. Just getting started with the nRF51422, so forgive my being a bit "green."
Background: Testing with nRF5_SDK_12.3.0_d7731ad, Keil V5.18A on...
I was looking for a way to connect multiple nrf52832 via ble and connect the master to a smartphone app. Right now I'm focussing on connecting two nrf52832 through BLE. Can...
Hi there,
I see the "Error 133 (0x85): GATT ERROR" in the nrfconnect App with an HTC U11 Life with up to date Android (8.0.0).
I tested the nordic ble_app_uart example...
I am setting up the Power Profiler kit as standalone, no DK, measuring external target, also use the Segger jLink as interface. With the 2.0 software, it could not connect...
hello ,
can anyone guide how to add custom service and charactericteristic and receive data from nrf connect app using handler
i am using
board :PCA10040
nRF52DK ...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
