Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
I am trying to run pb remote example but i'm stuck at command 3 it only shows "Got event 0" not goes further to receive remote uuid.
0> 1) Provision first available device...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
I am new to Nordic and BLE mesh connectivity. I have the following assumptions & queries, Please clarify if I am wrong.
1. Is it possible to implement BLE Mesh using Thing52...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
I am using the nrf52832 and according to the errata v1.1 the same contains a problem in the spi, according to clause 3.13 the engineering versions (QFAA-AA0, QFAA-AC0) and...
