In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi Team,
There are many ways to implement PWM in nRF52.
Can someone help me understand which is the most power-optimized way along with the softdevice? Using PWM peripheral...
After disconnecting from chip I can not connect it with the same phone .And the chip will restart when we try to reconnet with the same phone (the phone have been deleted...
Dear friend,
The user experience of PPK desktop application is terrible. There is no guider about using this application in the PPK user guider 2.0. I got some problems...
Hi,
we are using the PPK for a while (Software version 1.0.0). For some reason the calibrated values haved changed and very high current values are showing up. I've recalibrated...
Hi Team,
S132 V5.0 for nRF52832 can support up to 20 links.
If the connected links have different ATT MTU setting, what is the behavior of the device/softdevice regarding...
Hi,
I am using nRF52832 SDK 14.2.0 and i added the header file in project path "nrf_dfu_svci.h" but still i getting the error ..\..\..\..\..\..\components\libraries\bootloader...
Hi all,
I am using segger studio , i am trying to run examples of mesh alpha sdk that nordic provides. I can able to dump the code on board successfully. But if i try to...
I am using the nrf_i2s driver, and it works properly ... with CONFIG.CHANNELS set to stereo.
But for my application, I only need to drive data onto SDOUT left channel. ...
Dear sir please help..its urgent.
i am using below configurations. Nordic - nRF52832-QFAA-B Soft device - 132 SDK - nRF5_SDK_14.2
I am following the "ble_app_att_mtu_throughput...
Hi all,
I am using the nRF51822 BLE with custom board, I want to configure Timer1 to generate IRQ for every 1ms and Timer2 to generate IRQ for every 1us. I want to run...
Hi,
I want to change the UART0 baud rate at runtime (the peripheral has switched to a new rate). Is it enough to reset to (say) 9600 baud, like:
NRF_UART0->BAUDRATE =...
Hello,
I am using the nRF52840 DK with Keil to develop. I have a structure defined as follows:
I have verified that uint8 is 1 byte, uint16 is 2 bytes, and uint32 is...
Hi,
I am using nRF52832 Dk and SD132, sdk is 13.1. I have sent my sensor data to server using external wifi module which is interface with nRF52832 DK.
Everything working...
I have a Client and two Server, so i did flash the example code.
But, from the command '3', i get an error that i do not know.
Can you help me ?
What is correct value...
Hi.
I want to add constant descriptor. Can I save the memory using const variable and BLE_GATTS_VLOC_USER. Will it occur some faults in future?
static const uint8_t value...
