I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
Hi,
I am downloading my code to my custom board and sending commands through a USB virtual COM port. I basically echo and execute some GPIO operations after decoding the...
I have installed NRF 5X command line but I don't see it in my programs/start / desktop where will be the .exe file or how can I open that? How can I work with that ?
Hello ,
I am using 4 nrf52 DK for Mesh
1. how to I configure a Node as Relay
2. How do I capture MESH Packets/ Data from Mesh in Raspberry Pi and send to cloud
hi,
When working with Keil are the NRF_SDH_CLOCK_LF_RC_TEMP_CTIV & NRF_SDH_CLOCK_LF_RC_CTIV compiled as part of the nrf52810_xxaa project?
if not how can I compile...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
I started with the ble_app_template and a preexisting project written with sdk 12.
I have a custom service and 2 characteristics.
The point I am at now is that my DK advertises...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
